Investigating a factor that affects the rate of re Essay Example For Students

Investigating a factor that affects the rate of re Essay actionAim To investigate the effect of concentration on the rate of reaction To investigate the reaction between hydrochloric acid and magnesiumPrediction 1) -I predict that the higher the concentration of hydrochloric acid the faster the time will be for the magnesium to dissolve. 2) -I predict that the higher the molar of hydrochloric acid, the more hydrogen gas will be given off. 3) -I predict that the higher the concentration of hydrochloric acid the faster the rate of reaction. This will therefore mean that the rate of reaction will be faster. 4) I predict that when I double the concentration, I would expect the rate of reaction to double with the concentration. ReasonsRates of Reaction measures different reaction rates and tells us things that affect the speed of a reaction. Seven factors that affect how fast a reaction takes place are: Temperature Catalyst Pressure PH Surface area Concentration LightWe can change speeds of reactions in three ways- Increasing the surface area Increasing concentration Raising the temperature Adding a catalyst There are three ways to measure the speed of a reaction and these are precipitation, change in mass and the volume of gas given off. The four things that are suitable for the magnesium reaction to affect how fast it takes place are Temperature Turbulence Concentration Surface areaConcentration is the best factor to for this magnesium and hydrochloric acid reaction because it is easy to undertake. In this experiment between hydrochloric acid and magnesium ribbon. The hydrochloric acid will dissolve the magnesium strip. This should produce hydrogen gas. The chemical equation for this reaction isMg (s) + 2HCL (aq) Mg Cl (aq) + H (g) This chemical reaction involves reactants which when mixed may cause a chemical reaction. This in turn may produce different products. What I am expecting to see in the beaker is the magnesium and hydrochloric acid reacting together to form fizzing in the solution and I think I will also see bubbles, which I may see slowly or fast depending on the amount ofconcentration. Magnesium will eventually break away and eventually dissolve. The concentration of the hydrochloric solution affects the rate of the reaction. If the concentration is too high, there will be more collisions between the enzymes, which will also increase the rate of reaction. On the other hand, if the concentration is to low then the collisions of enzymes with substrates will slow down or stop making the rate of reaction slower. This means that there will be less frequent collisions between the atoms. When there are more particles (reactants) present, the more likely a collision, and so the higher the reaction rate.Source (GCSE Bitesize chemistry, by David Smith) These factors will affect the rate of reaction. This is because of the collision theory. The collision theory shows us that it is necessary for the reacting particles to collide with each other particles. This is so there is enough energy to form or break bonds between the particles. If however, the particles do not have enough energy then the particles will bounce back not causing a collision. The minimum amount of energy needed for a co llision to take place between the particles is called the activation energy. Source (GCSE chemistry revision guide, by Ian Lee)The Maxwell Boltzmann curve is a graph that predicts the probability that the different particles will collide with each other at different temperatures. On the graph shown below the dark shaded area shows the particles that have enough energy to collide with each other. The very light shaded area is the particles that do not have enough energy to collide because they do not have enough energy. The line on the graph showing the activation energy is the minimum amount of energy that is needed for the particles to collide. This Maxwell Boltzmann curve can be related to the reaction between magnesium and hydrochloric acid because the graph shows us how much energy is needed for the particles to make and break new bonds. The Maxwell Boltzmann curve is shown below The equation Ka shows the number of variables that are acting on the reaction between magnesium an d hydrochloric acid. K = rate constantA = the reactant M = the order of the reaction The rate constant is the amount of hydrochloric acid this is 25 ml. The reactant used is the concentration of the hydrochloric acid. The order of reaction is calculated by the number of variables that the reaction uses. In this, case the order of reaction is one. This is because the only variable in the reaction is concentration. Apparatus Hydrochloric acid (0.1 molar, 0.5 molar, 1 molar, 3 molar, 2 molar, 5 molar) Measuring cylinder to measure the amount of hydrogen gas given off Water used in the experiment Magnesium strips Used to react with the hydrochloric acid Stop watch to measure the time of how long the reaction takes place Water basin to put the water in Beaker to put the solution inDiagramFair Test-To make this a fair test I have to take a number of precautions. The first precaution I will take will be to keep the temperature of the hydrochloric acid the same. This will ensure t hat the rate of reaction is not increased by the temperature. I will also keep the volume of hydrochloric acid the same. This will make the test fair because then the volume of the acid will not affect the rate of reaction. I will also try to keep the surface area of the magnesium the same. This will make the test fair because it will then not speed up the rate of reaction in the experiment. Safety To ensure safety I will also check that the tube containing the hydrogen gas will contain no leaks. This is so it does not make the test unfair if the hydrogen gas leaks. Federalism From Its Beginning to the Present EssayThe general trend on the line graph (Fig 3) shows that as the concentration of the hydrochloric acid increased the rate of reaction also increased. This was because as the concentration increased the number of particles colliding with each other also increased. Concentration molar 5.0 was the fastest concentration because the rate at which the magnesium dissolved was quickest for the concentration. The concentration with molar 5.0 had the highest rate of reaction. This meant that the 0.1 concentration had the lowest rate of reaction. The reaction between hydrochloric acid magnesium is an exothermic reaction, which means that this reaction gives out heat. As this reaction gives off heat, this process will affect the rate of reaction. This should affect the rate of reaction graph (Fig 3) but I found out that my rate of reaction graph was unaffected. The conclusion I have made is based on the collision theory. The collision theory shows us that when there is enough energy in the particle the reactant can break or form bonds. In this case, the concentration increased the speed at which the particles collide. This means that as the concentration increased the speed of particles colliding increased because the particles had more energy. EvaluationTo improve this reaction between magnesium and hydrochloric acid I could have used more reliable equipment that measured more accurately. T his would have improved the accuracy of the results. We could have also used precise measuring equipment to measure the hydrochloric acid and the magnesium. This would have given us results that are more accurate. To improve the accuracy of the experiment we could have repeated the investigation more times than 3 times. This would have given us results that are more accurate. To further improve the investigation we could have used different rates of concentration. This would have given a wider range of results. To enhance the experiment further we should keep the room temperature constant. This would help the accuracy of the experiment because if the temperature were constant the rate of reaction would not be affected by the temperature. To improve our investigation in the future we could have used a more accurate stopwatch or used a better device of checking if the magnesium had fully dissolved. To improve our investigation in the future we could have used a logiests data logger. This would have helped us to achieve more accurate results in the investigation. In my investigation, there were a few abnormal results when compared to the overall average. For the 0.1 concentration the result was 3325.8, however the average time for 0.1 concentration was 3427.3. This means that the result is abnormal because the reading is not equal to the average time. For the 0.5 concentration the result was 510.4, however the average time for the 0.5 concentration was 532.3. This means that the result is abnormal because the findings are not equal to the average time. For the 1.0 concentration the result was 79.2, however the average time for 1.0 concentration was 70.69. This means that the result is abnormal because the reading is not equal to the average time. For the 3.0 concentration the result was 12.5, however the average time for 3.0 concentration was 11.81. This means that the result is abnormal because the findings are not equal to the average time. I think that the abnormal results were caused by either wrong measurements of hydrochloric acid or th e inability to view when the magnesium strip had dissolved. This would mean that the results would be higher or lower than the average time result. When we completed our experiment, we could have investigated further by experimenting with different concentrations of hydrochloric acid or different lengths of magnesium. This would have given us a wider range of results. Bibliography Text Books GCSE Chemistry Science Written by Alain Anderton, Second EditionGCSE Bitesize Science Chemistry revision guide, written by David SmithOCR Chemistry Text book Written by David LeePeople Shila Tailor this person helped me with this investigation. Mrs Kemp my Science, Biology teacher Mrs Zanab this teacher helped me with this investigationElectronicElectronic services also helped me with my report. This included the use of the internet. The websites used to get the information included: www.Sciencerevision.co.ukwww.Bitsize.com/Chemistry www.ChemistryInfo.co.ukwww.OCR-Chemistry.co.ukIn this inv estigation, I also used e-mail to help with my investigation.